"Quality" is always the essence of Lancool's products, All products are manufactured in Taiwan and
distributed to worldwide markets.
|
|
|
The Dragon Lord K serires builds LanCool’s high standard of Quality requirement. This SECC steel cases
features a black interior with completely tool-less design are the perfect complement to a PC gamer’s
needs.
|
LanCool redesigned the internal layout for a better thermal solution, Dragon Lord k62 uses large size
cooling fans to remove the system heat faster and quieter as well as keeps the system more stable.
|
|
|
The cutting edge tool-less design is an important key feature in 2009 LanCool cases. LanCool designer
considered end user requirements, like those who need to build systems faster, or swap out components
often. The brand new tool-less modules can make users’ life much more convenient.
|
The look of Dragon Lord k62 has no door panel design; users can access the external drive easier. The
two red stripes on the front panel done in attractive anodized aluminum give a flamboyant finishing
touch to this outstanding high-end chassis.
|
|
|
The hardware installation with Dragon Lord k62 is very easy and simple. The front panel and top panel
are detachable and they can be removed without tools.
|
The Dragon Lord k62 is targeted for the LAN party gamers. It is a mid-tower case, which is ideal for
the latest graphics cards in combination with the best thermal dynamics. All the internal installation
can be done without tools, and is easily adjustable to optimize your hardware setup. Especially in the
advent of adding in new graphics cards, equipped with 8 PCI slots, can hold three or more graphics
cards, supports CrossfireX™ and 3-way SLI™.
|
|
|
The new internal layout has the motherboard on top of the power supply unit, which allows for easier
access to the motherboard as well as more room above, thus larger CPU coolers can be used. The power
supply unit at the button of the case is cooled with fresh cool air directly from the outside of the
case, instead of pre-heated air from within. This will bring down the core temperatures and extend the
lifespan of the PSU significantly.
|
To install motherboard require no tools, use tool-less screw to screw a motherboard on case, easily and
quickly.
| |
| The Dragon Load k62 is equipped with large cooling fans, with
low RPM, which still provide enough air flow to cool down the hardware adequately. The front 140mm
intakes blue LED fan runs at 1000RPM. The top two silent 140mm ball-bearing blue LED fans exhaust the
hot air out at 1000RPM, and the rear 120mm fan extracts the hot air out at 1500RPM.
|
The fans on the top panel are mounted with Lian Li’s new anti-vibration fan mounting system; the rubber
ring grommet absorbs the vibration, keeping the case silent.
|
|
|
The new 5.25” bay tool-less mounting incorporates a mounting bar equipped with rubber padding. After
secure the mounting bar, the rubber pad pushes and holds the 5.25” device in position to secure and
absorb vibration from the device. |
The too-less HDD cage combines with patented anti-vibration rubber grommets to suspend the HDD’s in a
noise free environment. The two buckls on both side to hold the HDD in position, also absorb and reduce
vibrations.
|
|
| The aluminum PCI tool-less mounting module is equipped with a
rubber pad which can hold the graphics card firmly while closing the gap found in the PCI bracket and
PCI slot to reduce noise from escaping air and furthermore reduce vibrations.
|
The Power Supply has rubber pads for both insulation and support. The mounting clip is also aligned
with rubber to reduce vibrations but also and also secure the PSU without scratching the painted
surface.
|
|
|
There are special air intake vents at the front of the case, allow cold air to enter , also keep system
noise inside the case.
|
There are four rubber grommets between the HDD cage and HDD, avoid HDD directly contact the HDD cage,
absorb and reduce vibrations, keep the noise down.
|
|
|
Dragon Load k62 inputs cold air by the 140mm (1000RPM) intake fan, There are also vents on the 5.25”
bezels, allow cold air to enter the case to cool the system down
|
The two 140mm blue LED fans on the top cover and the 120mm fan at the rear exhaust the hot air out from
the system. The fans cover the whole motherboard, and they can remove the heat fast.
|
|
|
The rear 120mm exhaust fan just next to the CPU, it can remove the hot air out fast and silently.
|
There are vents on the PCI slots, provids extra cooling to graphics card.
|
|
|
The power supply unit is at the bottom of the case. It can draw in cold air directly through the vent
below the power supply unit. This cooler, fresh air will keep your PSU components more cool and stable
and thus extend the PSU lifecycle.
|
Dragon Load k62 supports liquid cooling system, the two holes at the rear of the case allows water
tubes to pass through, and the rubber cover can protect the tubes away from cutting.
|
|
|
The Dragon Load k62 feature a high density vent design, to make sure fans remove the system hot air out
of the case totally.
|
2009 has seen an all-new tool-less design from Dragon Lord K series chassis. To do this required a
great many innovative patents to be filed worldwide. The ideas will make installing and maintenance
much easier. For example when installing the 5.25” optical drive, just slide the drive into the 5.25”
bay, and close the mounting bar to secure the optical drive, as simple as that.
|
|
|
The installation of the hard disk is very easy, and tool-less. Place the hard disk into the aluminum
cage, and fasten the bucks to secure the hard disk.(2.5" HDD install feasible), Slide the hard disk
within the cage into the special hard disk rack with the rubber suspension grommet.
|
To install PCI add-on cards require no tools at all. Simply open the aluminum arm of the tool-less PCI
add-on card holder, insert the add-on card to the motherboard slots, and close the aluminum arm to hold
the add-on card in position. The additional rubber padding on the aluminum arm assists in gripping the
card bracket and securing it firmly.
|
|
|
To install PSU require no tools. Simply open the aluminum PSU holder, insert the PSU in position, also
can turn PSU's fans up or down to suit your need, then close the aluminum PSU holder.
|
The fans on the top panel are mounted with special screws with
rubber ring suspension grommets. These allow easy access and removal of the fan for cleaning or
service. |
|
| The intake fans are aligned with inlet holes on the bezels.
These are equipped with air filters to stop the dust and keep the internals dust free and clean.<
|
There is an air filter at the base of the case to stop dust
from entering the case. The filter is washable. The vents are specially designed to retard heat and
fire crossover should a short circuit cause sparks and excessive heat within your system. This feature
is designed to prevent the problem from spreading outside your case should the unlikely event occur
with your components. |
|